Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Flow, velocity & diameter

Define the pipe. Follow the flow.

Pipe Velocity Calculator

Calculate average liquid or actual-volume gas velocity from bore and volume flow.

Your pipe & operating inputs

mm
L/s

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Q = A v; A = πD²/4. v = 4Q/(πD²).

Calculate average liquid or actual-volume gas velocity from bore and volume flow.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Gas volume flow must be at the actual pipe pressure and temperature, not an unconverted SCFM reference.

Pipe Velocity: assumptions and applications

Calculate average liquid or actual-volume gas velocity from bore and volume flow. Gas volume flow must be at the actual pipe pressure and temperature, not an unconverted SCFM reference.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe Velocity Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Actual volume flow = 2 L/s.

OutputComputed result
Mean actual-volume flow velocity1.018592 m/s
Velocity in feet per second3.341836 ft/s
Bore area0.001963 m²
Actual flow2 L/s
Actual flow7.2 m³/h
US gallons per minute31.700646 US gpm
Imperial gallons per minute26.39631 Imp gpm
Actual cubic feet per minute4.23776 acfm

How the stated input changes the result

ScenarioChanged input / basisResult
1 L/sActual volume flow0.509296 m/s
1.5 L/sActual volume flow0.763944 m/s
2 L/sActual volume flow1.018592 m/s
2.5 L/sActual volume flow1.27324 m/s
3 L/sActual volume flow1.527887 m/s
4 L/sActual volume flow2.037183 m/s

Unchanged inputs use: Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Actual volume flow = 2 L/s. Results retain the model limitations described above.

Common questions

How do I calculate velocity from GPM and diameter?

Convert US gpm to m³/s by multiplying by 0.003785411784/60, convert bore to metres, and divide by πD²/4. The result is mean speed in m/s.

Can I calculate velocity from pressure alone?

Pressure must be combined with a stated energy balance and resistance model. Use the liquid pressure-flow tool or a gas model appropriate to the operating state.

How do I use this pipe velocity calculator?

Calculate average liquid or actual-volume gas velocity from bore and volume flow. Q = A v; A = πD²/4. v = 4Q/(πD²).

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • US DOE — DOE-HDBK-1012/3-92, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors