Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Pressure loss & resistance

Define the pipe. Follow the flow.

Pipe Pressure Drop Calculator

Solve pipe pressure drop with flow-dependent Darcy friction and explicitly entered fluid properties.

Your pipe & operating inputs

mm
m
mm
kg/m³
mm²/s
L/s

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Δp = (fD L/D + ΣK) ρv²/2; Re = vD/ν. Laminar fD=64/Re; turbulent fD solves Colebrook.

Solve pipe pressure drop with flow-dependent Darcy friction and explicitly entered fluid properties.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Steady, full, circular, single-phase incompressible flow. Reynolds numbers from 2000 through 4000 are deliberately rejected; this calculator does not interpolate uncertain transition flow. Roughness/diameter must not exceed 0.05.

Pipe Pressure Drop: assumptions and applications

Solve pipe pressure drop with flow-dependent Darcy friction and explicitly entered fluid properties. Steady, full, circular, single-phase incompressible flow. Reynolds numbers from 2000 through 4000 are deliberately rejected; this calculator does not interpolate uncertain transition flow. Roughness/diameter must not exceed 0.05.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe Pressure Drop Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Straight pipe length = 30 m; Absolute roughness (example) = 0.045 mm; Sum of minor-loss K = 0 ; Fluid density = 998.2 kg/m³; Kinematic viscosity = 1.004 mm²/s; Actual volume flow = 2 L/s.

OutputComputed result
Friction pressure loss7.362006 kPa
Pressure loss7.362006 kPa
Pressure loss1.067769 psi
Fluid head loss0.752069 m
Mean velocity1.018592 m/s
Reynolds number50,726.675089
Darcy friction factor0.023695
Relative roughness0.0009
Actual flow2 L/s
Actual flow7.2 m³/h
US gallons per minute31.700646 US gpm
Imperial gallons per minute26.39631 Imp gpm
Actual cubic feet per minute4.23776 acfm

How the stated input changes the result

ScenarioChanged input / basisResult
15 mStraight pipe length3.681003 kPa
22.5 mStraight pipe length5.521505 kPa
30 mStraight pipe length7.362006 kPa
37.5 mStraight pipe length9.202508 kPa
45 mStraight pipe length11.043009 kPa
60 mStraight pipe length14.724012 kPa

Unchanged inputs use: Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Straight pipe length = 30 m; Absolute roughness (example) = 0.045 mm; Sum of minor-loss K = 0 ; Fluid density = 998.2 kg/m³; Kinematic viscosity = 1.004 mm²/s; Actual volume flow = 2 L/s. Results retain the model limitations described above.

Common questions

What is the difference between major and minor losses?

Major loss is distributed wall friction over straight length. Minor loss represents fittings, entrances and other local features using coefficients referenced to the appropriate velocity.

How do pipe length and flow change pressure drop?

At a fixed flow and bore, straight-pipe friction increases with length. Flow changes both velocity and Reynolds-dependent friction, so pressure drop is not generally proportional to flow.

Can I convert PSI directly to GPM?

Pressure alone is insufficient. This model also uses actual bore, length, roughness, minor losses, density and viscosity. Enter only the pressure available for friction after other energy terms are accounted for.

How do I use this pipe pressure drop calculator?

Solve pipe pressure drop with flow-dependent Darcy friction and explicitly entered fluid properties. Δp = (fD L/D + ΣK) ρv²/2; Re = vD/ν. Laminar fD=64/Re; turbulent fD solves Colebrook.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • US DOE — DOE-HDBK-1012/3-92, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
  • US EPA — EPANET 2.2 User Manual, Chapter 12: Analysis Algorithmshttps://raw.githubusercontent.com/USEPA/EPANET2.2/master/User_Manual/docs/12_analysis_algorithms.rst
  • Brkić and Praks (2019) — Accurate and Efficient Explicit Approximations of the Colebrook Flow Friction Equation Based on the Wright ω-Functionhttps://www.mdpi.com/2227-7390/7/1/34
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors