Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Flow, velocity & diameter

Define the pipe. Follow the flow.

Pipe Diameter Calculator

Calculate a continuous bore from a flow and a chosen velocity.

Your pipe & operating inputs

L/s
m/s

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

D = √(4Q/(πv)).

Calculate a continuous bore from a flow and a chosen velocity.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

This is a velocity-based diameter, not a nominal size, pressure-loss check or code sizing chart.

Pipe Diameter: assumptions and applications

Calculate a continuous bore from a flow and a chosen velocity. This is a velocity-based diameter, not a nominal size, pressure-loss check or code sizing chart.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe Diameter Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Actual volume flow = 2 L/s; Chosen mean velocity = 1.5 m/s.

OutputComputed result
Continuous velocity-based bore41.202582 mm bore
Inside diameter1.622149 in
Chosen velocity1.5 m/s

How the stated input changes the result

ScenarioChanged input / basisResult
1 L/sActual volume flow29.134625 mm bore
1.5 L/sActual volume flow35.682482 mm bore
2 L/sActual volume flow41.202582 mm bore
2.5 L/sActual volume flow46.065887 mm bore
3 L/sActual volume flow50.46265 mm bore
4 L/sActual volume flow58.26925 mm bore

Unchanged inputs use: Actual volume flow = 2 L/s; Chosen mean velocity = 1.5 m/s. Results retain the model limitations described above.

Common questions

Is pipe diameter from flow rate a nominal pipe size?

No. The answer is a continuous inside diameter at the velocity you choose. A supplier size must then be checked using its actual wall, bore and loss constraints.

Can this size chilled-water, oil or hot-water pipes?

It can calculate the continuity bore if actual volume flow and selected velocity are known. Fluid temperature, viscosity, pressure loss and installation requirements need separate checks.

How do I use this pipe diameter calculator?

Calculate a continuous bore from a flow and a chosen velocity. D = √(4Q/(πv)).

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • US DOE — DOE-HDBK-1012/3-92, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors