Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Heat transfer & expansion

Define the pipe. Follow the flow.

Pipe Outlet Temperature Calculator

Estimate constant-property fluid outlet temperature along a pipe.

Your pipe & operating inputs

mm
m
kg/s
J/(kg·K)
W/(m²·K)
°C
°C

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Tout=Ta+(Tin−Ta) exp[−U πDo L/(ṁcp)].

Estimate constant-property fluid outlet temperature along a pipe.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

U uses the stated outside-diameter area. Single-phase sensible heat only; no phase change, variable properties or heat generation.

Pipe Outlet Temperature: assumptions and applications

Estimate constant-property fluid outlet temperature along a pipe. U uses the stated outside-diameter area. Single-phase sensible heat only; no phase change, variable properties or heat generation.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe Outlet Temperature Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Outside diameter = 60.3 mm; Straight pipe length = 100 m; Mass flow = 0.2 kg/s; Specific heat capacity = 4180 J/(kg·K); Overall U on outside pipe area = 5 W/(m²·K); Fluid inlet temperature = 80 °C; Constant surroundings temperature = 20 °C.

OutputComputed result
Constant-property fluid outlet temperature73.572951 °C
Signed heat released5,373.01271 W

How the stated input changes the result

ScenarioChanged input / basisResult
50 mStraight pipe length76.695477 °C
75 mStraight pipe length75.112104 °C
100 mStraight pipe length73.572951 °C
125 mStraight pipe length72.076784 °C
150 mStraight pipe length70.6224 °C
200 mStraight pipe length67.834352 °C

Unchanged inputs use: Dimension units = Metric (m / mm); Outside diameter = 60.3 mm; Straight pipe length = 100 m; Mass flow = 0.2 kg/s; Specific heat capacity = 4180 J/(kg·K); Overall U on outside pipe area = 5 W/(m²·K); Fluid inlet temperature = 80 °C; Constant surroundings temperature = 20 °C. Results retain the model limitations described above.

Common questions

What is the main limitation of this calculation?

U uses the stated outside-diameter area. Single-phase sensible heat only; no phase change, variable properties or heat generation.

How are the comparison-table numbers generated?

Each row changes the labelled straight pipe length from the worked example. The other printed inputs remain fixed. The table uses the same Tout=Ta+(Tin−Ta) exp[−U πDo L/(ṁcp)]. method as the form.

How do I use this pipe outlet temperature calculator?

Estimate constant-property fluid outlet temperature along a pipe. Tout=Ta+(Tin−Ta) exp[−U πDo L/(ṁcp)].

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • US DOE Fundamentals Handbook 1012/2-92: Heat Transfer, HT-02 pp. 11-27https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL2.pdf
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors