Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Gravity drainage & Manning

Define the pipe. Follow the flow.

Pipe Slope and Invert Calculator

Calculate signed fall, percent grade, angle and fall per foot.

Your pipe & operating inputs

m
m
m

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

S = (upstream invert − downstream invert)/horizontal run.

Calculate signed fall, percent grade, angle and fall per foot.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Length is horizontal plan run. This geometric slope does not choose a code minimum or account for settlement.

Pipe Slope and Invert: assumptions and applications

Calculate signed fall, percent grade, angle and fall per foot. Length is horizontal plan run. This geometric slope does not choose a code minimum or account for settlement.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe Slope and Invert Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Straight pipe length = 30 m; Upstream invert elevation = 10 m; Downstream invert elevation = 9.7 m.

OutputComputed result
Signed invert slope1 %
Signed fall0.3 m
Slope0.01 m/m
Angle0.572939 degrees
Fall per foot0.12 in/ft

How the stated input changes the result

ScenarioChanged input / basisResult
15 mStraight pipe length2 %
22.5 mStraight pipe length1.333333 %
30 mStraight pipe length1 %
37.5 mStraight pipe length0.8 %
45 mStraight pipe length0.666667 %
60 mStraight pipe length0.5 %

Unchanged inputs use: Dimension units = Metric (m / mm); Straight pipe length = 30 m; Upstream invert elevation = 10 m; Downstream invert elevation = 9.7 m. Results retain the model limitations described above.

Common questions

What is the main limitation of this calculation?

Length is horizontal plan run. This geometric slope does not choose a code minimum or account for settlement.

How are the comparison-table numbers generated?

Each row changes the labelled straight pipe length from the worked example. The other printed inputs remain fixed. The table uses the same S = (upstream invert − downstream invert)/horizontal run. method as the form.

How do I use this pipe slope and invert calculator?

Calculate signed fall, percent grade, angle and fall per foot. S = (upstream invert − downstream invert)/horizontal run.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Elementary Algebra 2e: slope as rise over runhttps://openstax.org/books/elementary-algebra-2e/pages/4-4-understand-slope-of-a-line
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors