Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Gravity drainage & Manning

Define the pipe. Follow the flow.

Pipe Normal Depth Calculator

Find normal water depth in a circular gravity pipe and report a second root when it exists.

Your pipe & operating inputs

mm
L/s
m/m
s/m⅓

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Q = (1/n) A R^(2/3) √S; θ=2acos(1−2y/D), A=D²(θ−sinθ)/8, R=A/(Dθ/2). Solve Q(y)=target on each physical branch.

Find normal water depth in a circular gravity pipe and report a second root when it exists.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Uniform free-surface flow, constant slope and roughness. No inlet control, downstream backwater, surcharge, perforation inflow or culvert routing is modeled. Above the full-section discharge, two depths can be possible; neither alone selects the real downstream-controlled state.

Pipe Normal Depth: assumptions and applications

Find normal water depth in a circular gravity pipe and report a second root when it exists. Uniform free-surface flow, constant slope and roughness. No inlet control, downstream backwater, surcharge, perforation inflow or culvert routing is modeled. Above the full-section discharge, two depths can be possible; neither alone selects the real downstream-controlled state.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe Normal Depth Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Actual inside diameter = 300 mm; Actual volume flow = 30 L/s; Uniform bed slope = 0.005 m/m; Manning n (example) = 0.013 s/m⅓.

OutputComputed result
Lower-branch normal water depth139.048466 mm
Lower branch depth ratio0.463495 y/D
Full-section discharge68.377762 L/s
Maximum free-surface discharge73.554378 L/s
Depth ratio at maximum0.938181 y/D

How the stated input changes the result

ScenarioChanged input / basisResult
15 L/sActual volume flow95.460046 mm
22.5 L/sActual volume flow118.449671 mm
30 L/sActual volume flow139.048466 mm
37.5 L/sActual volume flow158.502783 mm
45 L/sActual volume flow177.599618 mm
60 L/sActual volume flow217.897826 mm

Unchanged inputs use: Dimension units = Metric (m / mm); Actual inside diameter = 300 mm; Actual volume flow = 30 L/s; Uniform bed slope = 0.005 m/m; Manning n (example) = 0.013 s/m⅓. Results retain the model limitations described above.

Common questions

Why can a circular pipe have two normal depths?

Near the top, increasing water depth adds relatively little area but more wetted perimeter. Discharge reaches a maximum before the pipe becomes full, allowing two depths for some target flows.

Does the lower root predict actual sewer water level?

Not by itself. Boundary conditions and backwater may control actual depth. The tool reports ideal uniform-flow solutions, not a downstream-controlled profile.

How do I use this pipe normal depth calculator?

Find normal water depth in a circular gravity pipe and report a second root when it exists. Q = (1/n) A R^(2/3) √S; θ=2acos(1−2y/D), A=D²(θ−sinθ)/8, R=A/(Dθ/2). Solve Q(y)=target on each physical branch.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • US Bureau of Reclamation — Water Measurement Manual, Chapter 2, Section 16: Normal Flow Equations and Friction Head Losshttps://www.usbr.gov/tsc/techreferences/mands/wmm/chap02_16.html
  • Missouri DOT — Engineering Policy Guide 750.1: Open Channelshttps://epg.modot.org/index.php/750.1_Open_Channels
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors