Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Pressure loss & resistance

Define the pipe. Follow the flow.

Colebrook Friction Factor Calculator

Solve the implicit turbulent Colebrook equation, or 64/Re for laminar flow.

Your pipe & operating inputs

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

1/√fD = −2 log10[(ε/D)/3.7 + 2.51/(Re√fD)].

Solve the implicit turbulent Colebrook equation, or 64/Re for laminar flow.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Outputs are Darcy factors, four times the Fanning factor. Re from 2000 through 4000 is rejected.

Colebrook Friction Factor: assumptions and applications

Solve the implicit turbulent Colebrook equation, or 64/Re for laminar flow. Outputs are Darcy factors, four times the Fanning factor. Re from 2000 through 4000 is rejected.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Colebrook Friction Factor Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Reynolds number = 100000 ; Relative roughness ε/D = 0.0009 .

OutputComputed result
Darcy friction factor0.021832 Darcy
Fanning factor0.005458 Fanning

How the stated input changes the result

ScenarioChanged input / basisResult
50000 Reynolds number0.023744 Darcy
75000 Reynolds number0.022526 Darcy
100000 Reynolds number0.021832 Darcy
125000 Reynolds number0.02138 Darcy
150000 Reynolds number0.02106 Darcy
200000 Reynolds number0.020635 Darcy

Unchanged inputs use: Reynolds number = 100000 ; Relative roughness ε/D = 0.0009 . Results retain the model limitations described above.

Common questions

What is the main limitation of this calculation?

Outputs are Darcy factors, four times the Fanning factor. Re from 2000 through 4000 is rejected.

How are the comparison-table numbers generated?

Each row changes the labelled reynolds number from the worked example. The other printed inputs remain fixed. The table uses the same 1/√fD = −2 log10[(ε/D)/3.7 + 2.51/(Re√fD)]. method as the form.

How do I use this colebrook friction factor calculator?

Solve the implicit turbulent Colebrook equation, or 64/Re for laminar flow. 1/√fD = −2 log10[(ε/D)/3.7 + 2.51/(Re√fD)].

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Brkić and Praks (2019) — Accurate and Efficient Explicit Approximations of the Colebrook Flow Friction Equation Based on the Wright ω-Functionhttps://www.mdpi.com/2227-7390/7/1/34
  • US EPA — EPANET 2.2 User Manual, Chapter 12: Analysis Algorithmshttps://raw.githubusercontent.com/USEPA/EPANET2.2/master/User_Manual/docs/12_analysis_algorithms.rst
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors