Pipe calculators / Pressure loss & resistance
Define the pipe. Follow the flow.
Pipe Flow from Pressure Calculator
Solve pipe flow from pressure with flow-dependent Darcy friction and explicitly entered fluid properties.
Your pipe & operating inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Δp = (fD L/D + ΣK) ρv²/2; Re = vD/ν. Laminar fD=64/Re; turbulent fD solves Colebrook.
Solve pipe flow from pressure with flow-dependent Darcy friction and explicitly entered fluid properties.
- Confirm the fluid state, geometry, flow regime and units.
- Enter actual dimensions and justified operating conditions.
- Submit the form, then interpret the result with the assumptions and limits below.
Steady, full, circular, single-phase incompressible flow. Reynolds numbers from 2000 through 4000 are deliberately rejected; this calculator does not interpolate uncertain transition flow. Roughness/diameter must not exceed 0.05.
Pipe Flow from Pressure: assumptions and applications
Solve pipe flow from pressure with flow-dependent Darcy friction and explicitly entered fluid properties. Steady, full, circular, single-phase incompressible flow. Reynolds numbers from 2000 through 4000 are deliberately rejected; this calculator does not interpolate uncertain transition flow. Roughness/diameter must not exceed 0.05.
Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.
A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.
Continue with: Pipe Pressure Drop Calculator · Pipe Head Loss Calculator · Pipe Reynolds Number Calculator · Colebrook Friction Factor Calculator
Check the numbers
Pipe Flow from Pressure Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Straight pipe length = 30 m; Absolute roughness (example) = 0.045 mm; Sum of minor-loss K = 0 ; Fluid density = 998.2 kg/m³; Kinematic viscosity = 1.004 mm²/s; Available friction pressure difference = 100 kPa.
| Output | Computed result |
|---|---|
| Flow for available friction pressure | 7.899133 L/s |
| Pressure loss | 100 kPa |
| Pressure loss | 14.503774 psi |
| Fluid head loss | 10.21555 m |
| Mean velocity | 4.022996 m/s |
| Reynolds number | 200,348.381656 |
| Darcy friction factor | 0.020633 |
| Relative roughness | 0.0009 |
| Actual flow | 7.899133 L/s |
| Actual flow | 28.43688 m³/h |
| US gallons per minute | 125.203814 US gpm |
| Imperial gallons per minute | 104.253984 Imp gpm |
| Actual cubic feet per minute | 16.737315 acfm |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 15 m | Straight pipe length | 11.283196 L/s |
| 22.5 m | Straight pipe length | 9.162102 L/s |
| 30 m | Straight pipe length | 7.899133 L/s |
| 37.5 m | Straight pipe length | 7.038158 L/s |
| 45 m | Straight pipe length | 6.403246 L/s |
| 60 m | Straight pipe length | 5.513229 L/s |
Unchanged inputs use: Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Straight pipe length = 30 m; Absolute roughness (example) = 0.045 mm; Sum of minor-loss K = 0 ; Fluid density = 998.2 kg/m³; Kinematic viscosity = 1.004 mm²/s; Available friction pressure difference = 100 kPa. Results retain the model limitations described above.
Common questions
How do I calculate water flow from PSI and pipe size?
Enter pressure available for friction, actual inside diameter, length, roughness, local-loss K, density and viscosity. The solver finds the supported laminar or turbulent flow branch.
Does this calculate maximum pipe flow?
Only the flow for the entered pressure and model assumptions. Other limits such as allowed speed, noise, cavitation, surge and pump operation are not optimized.
Can I convert PSI directly to GPM?
Pressure alone is insufficient. This model also uses actual bore, length, roughness, minor losses, density and viscosity. Enter only the pressure available for friction after other energy terms are accounted for.
How do I use this pipe flow from pressure calculator?
Solve pipe flow from pressure with flow-dependent Darcy friction and explicitly entered fluid properties. Δp = (fD L/D + ΣK) ρv²/2; Re = vD/ν. Laminar fD=64/Re; turbulent fD solves Colebrook.
Can I calculate in metric and imperial units?
The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.
Can I export this calculation to Excel?
Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.
What do the starting values mean?
They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.
Where are the formula sources?
The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- US DOE — DOE-HDBK-1012/3-92, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
- US EPA — EPANET 2.2 User Manual, Chapter 12: Analysis Algorithmshttps://raw.githubusercontent.com/USEPA/EPANET2.2/master/User_Manual/docs/12_analysis_algorithms.rst
- Brkić and Praks (2019) — Accurate and Efficient Explicit Approximations of the Colebrook Flow Friction Equation Based on the Wright ω-Functionhttps://www.mdpi.com/2227-7390/7/1/34
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors