Pipe calculators / Pressure loss & resistance
Define the pipe. Follow the flow.
Pipe Head Loss Calculator
Solve pipe head loss with flow-dependent Darcy friction and explicitly entered fluid properties.
Your pipe & operating inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
Δp = (fD L/D + ΣK) ρv²/2; Re = vD/ν. Laminar fD=64/Re; turbulent fD solves Colebrook.
Solve pipe head loss with flow-dependent Darcy friction and explicitly entered fluid properties.
- Confirm the fluid state, geometry, flow regime and units.
- Enter actual dimensions and justified operating conditions.
- Submit the form, then interpret the result with the assumptions and limits below.
Steady, full, circular, single-phase incompressible flow. Reynolds numbers from 2000 through 4000 are deliberately rejected; this calculator does not interpolate uncertain transition flow. Roughness/diameter must not exceed 0.05.
Pipe Head Loss: assumptions and applications
Solve pipe head loss with flow-dependent Darcy friction and explicitly entered fluid properties. Steady, full, circular, single-phase incompressible flow. Reynolds numbers from 2000 through 4000 are deliberately rejected; this calculator does not interpolate uncertain transition flow. Roughness/diameter must not exceed 0.05.
Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.
A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.
Continue with: Pipe Pressure Drop Calculator · Pipe Flow from Pressure Calculator · Pipe Reynolds Number Calculator · Colebrook Friction Factor Calculator
Check the numbers
Pipe Head Loss Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Straight pipe length = 30 m; Absolute roughness (example) = 0.045 mm; Sum of minor-loss K = 0 ; Fluid density = 998.2 kg/m³; Kinematic viscosity = 1.004 mm²/s; Actual volume flow = 2 L/s.
| Output | Computed result |
|---|---|
| Friction head loss | 0.752069 m head |
| Pressure loss | 7.362006 kPa |
| Pressure loss | 1.067769 psi |
| Fluid head loss | 0.752069 m |
| Mean velocity | 1.018592 m/s |
| Reynolds number | 50,726.675089 |
| Darcy friction factor | 0.023695 |
| Relative roughness | 0.0009 |
| Actual flow | 2 L/s |
| Actual flow | 7.2 m³/h |
| US gallons per minute | 31.700646 US gpm |
| Imperial gallons per minute | 26.39631 Imp gpm |
| Actual cubic feet per minute | 4.23776 acfm |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 15 m | Straight pipe length | 0.376035 m head |
| 22.5 m | Straight pipe length | 0.564052 m head |
| 30 m | Straight pipe length | 0.752069 m head |
| 37.5 m | Straight pipe length | 0.940087 m head |
| 45 m | Straight pipe length | 1.128104 m head |
| 60 m | Straight pipe length | 1.504139 m head |
Unchanged inputs use: Dimension units = Metric (m / mm); Actual inside diameter = 50 mm; Straight pipe length = 30 m; Absolute roughness (example) = 0.045 mm; Sum of minor-loss K = 0 ; Fluid density = 998.2 kg/m³; Kinematic viscosity = 1.004 mm²/s; Actual volume flow = 2 L/s. Results retain the model limitations described above.
Common questions
How are pressure loss and friction head related?
Head loss is pressure loss divided by density times gravity. One metre of head is not a fixed pressure for every liquid.
Is this pipe resistance the pump operating point?
No. The flow is supplied here. An operating point additionally requires the complete system energy balance and a compatible pump curve.
Can I convert PSI directly to GPM?
Pressure alone is insufficient. This model also uses actual bore, length, roughness, minor losses, density and viscosity. Enter only the pressure available for friction after other energy terms are accounted for.
How do I use this pipe head loss calculator?
Solve pipe head loss with flow-dependent Darcy friction and explicitly entered fluid properties. Δp = (fD L/D + ΣK) ρv²/2; Re = vD/ν. Laminar fD=64/Re; turbulent fD solves Colebrook.
Can I calculate in metric and imperial units?
The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.
Can I export this calculation to Excel?
Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.
What do the starting values mean?
They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.
Where are the formula sources?
The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- US DOE — DOE-HDBK-1012/3-92, Thermodynamics, Heat Transfer, and Fluid Flow, Volume 3https://www.energy.gov/sites/default/files/2026-04/DOE-HDBK-1012-92_VOL3.pdf
- US EPA — EPANET 2.2 User Manual, Chapter 12: Analysis Algorithmshttps://raw.githubusercontent.com/USEPA/EPANET2.2/master/User_Manual/docs/12_analysis_algorithms.rst
- Brkić and Praks (2019) — Accurate and Efficient Explicit Approximations of the Colebrook Flow Friction Equation Based on the Wright ω-Functionhttps://www.mdpi.com/2227-7390/7/1/34
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors