Pipe calculators / Nominal pipe & tube samples
Define the pipe. Follow the flow.
NPS 2 Schedule 40S Pipe Calculator
Calculate actual bore, cross section and capacity using a small published NPS 2 schedule 40S dimensional example.
Your pipe & operating inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ID=OD−2t; internal volume=πID²L/4.
Calculate actual bore, cross section and capacity using a small published NPS 2 schedule 40S dimensional example.
- Confirm the fluid state, geometry, flow regime and units.
- Enter actual dimensions and justified operating conditions.
- Submit the form, then interpret the result with the assumptions and limits below.
These editable dimensions are a limited supplier fact sample, not a complete ASME standard, tolerance table or pressure rating.
NPS 2 Schedule 40S Pipe: assumptions and applications
Calculate actual bore, cross section and capacity using a small published NPS 2 schedule 40S dimensional example. These editable dimensions are a limited supplier fact sample, not a complete ASME standard, tolerance table or pressure rating.
Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.
A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.
Continue with: NPS 1/2 Schedule 40S Pipe Calculator · NPS 1/2 Schedule 80S Pipe Calculator · NPS 3/4 Schedule 40S Pipe Calculator · NPS 3/4 Schedule 80S Pipe Calculator
Check the numbers
NPS 2 Schedule 40S Pipe Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Published outside diameter = 60.325 mm; Published wall thickness = 3.9116 mm; Straight pipe length = 3 m.
| Output | Computed result |
|---|---|
| Actual calculated bore | 52.5018 mm bore |
| Actual bore | 52.5018 mm |
| Actual bore | 2.067 in |
| Flow area | 0.002165 m² |
| Internal capacity | 6.494706 L |
| Internal capacity | 1.71572 US gal |
| Internal capacity | 1.428636 Imp gal |
| Internal capacity | 0.229358 ft³ |
| Internal capacity | 0.008495 yd³ |
| Petroleum barrels (42 US gal) | 0.04085 bbl |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 1.5 m | Straight pipe length | 52.5018 mm bore |
| 2.25 m | Straight pipe length | 52.5018 mm bore |
| 3 m | Straight pipe length | 52.5018 mm bore |
| 3.75 m | Straight pipe length | 52.5018 mm bore |
| 4.5 m | Straight pipe length | 52.5018 mm bore |
| 6 m | Straight pipe length | 52.5018 mm bore |
Unchanged inputs use: Dimension units = Metric (m / mm); Published outside diameter = 60.325 mm; Published wall thickness = 3.9116 mm; Straight pipe length = 3 m. Results retain the model limitations described above.
Common questions
Why is NPS different from measured inside diameter?
NPS is a nominal designation. Actual OD and the chosen wall schedule determine bore through ID=OD−2t.
Are the calculated tables full pipe standards?
No. They vary length for the single explicitly printed supplier dimension sample. They do not reproduce every nominal size or establish an allowable pressure.
How do I use this nps 2 schedule 40s pipe calculator?
Calculate actual bore, cross section and capacity using a small published NPS 2 schedule 40S dimensional example. ID=OD−2t; internal volume=πID²L/4.
Can I calculate in metric and imperial units?
The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.
Can I export this calculation to Excel?
Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.
What do the starting values mean?
They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.
Where are the formula sources?
The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- Penn Stainless: published pipe OD and schedule wall dimensions, incheshttps://www.pennstainless.com/resources/product-resources/pipe-dimensions/
- OpenStax Prealgebra: cylinder volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors