Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Nominal pipe & tube samples

Define the pipe. Follow the flow.

NPS 3/4 Schedule 80S Pipe Calculator

Calculate actual bore, cross section and capacity using a small published NPS 3/4 schedule 80S dimensional example.

Your pipe & operating inputs

mm
mm
m

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ID=OD−2t; internal volume=πID²L/4.

Calculate actual bore, cross section and capacity using a small published NPS 3/4 schedule 80S dimensional example.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

These editable dimensions are a limited supplier fact sample, not a complete ASME standard, tolerance table or pressure rating.

NPS 3/4 Schedule 80S Pipe: assumptions and applications

Calculate actual bore, cross section and capacity using a small published NPS 3/4 schedule 80S dimensional example. These editable dimensions are a limited supplier fact sample, not a complete ASME standard, tolerance table or pressure rating.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

NPS 3/4 Schedule 80S Pipe Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Published outside diameter = 26.67 mm; Published wall thickness = 3.9116 mm; Straight pipe length = 3 m.

OutputComputed result
Actual calculated bore18.8468 mm bore
Actual bore18.8468 mm
Actual bore0.742 in
Flow area0.000279 m²
Internal capacity0.836925 L
Internal capacity0.221092 US gal
Internal capacity0.184098 Imp gal
Internal capacity0.029556 ft³
Internal capacity0.001095 yd³
Petroleum barrels (42 US gal)0.005264 bbl

How the stated input changes the result

ScenarioChanged input / basisResult
1.5 mStraight pipe length18.8468 mm bore
2.25 mStraight pipe length18.8468 mm bore
3 mStraight pipe length18.8468 mm bore
3.75 mStraight pipe length18.8468 mm bore
4.5 mStraight pipe length18.8468 mm bore
6 mStraight pipe length18.8468 mm bore

Unchanged inputs use: Dimension units = Metric (m / mm); Published outside diameter = 26.67 mm; Published wall thickness = 3.9116 mm; Straight pipe length = 3 m. Results retain the model limitations described above.

Common questions

Why is NPS different from measured inside diameter?

NPS is a nominal designation. Actual OD and the chosen wall schedule determine bore through ID=OD−2t.

Are the calculated tables full pipe standards?

No. They vary length for the single explicitly printed supplier dimension sample. They do not reproduce every nominal size or establish an allowable pressure.

How do I use this nps 3/4 schedule 80s pipe calculator?

Calculate actual bore, cross section and capacity using a small published NPS 3/4 schedule 80S dimensional example. ID=OD−2t; internal volume=πID²L/4.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Penn Stainless: published pipe OD and schedule wall dimensions, incheshttps://www.pennstainless.com/resources/product-resources/pipe-dimensions/
  • OpenStax Prealgebra: cylinder volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors