Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Nominal pipe & tube samples

Define the pipe. Follow the flow.

Copper Type L Tube Capacity Calculator

Find bore and capacity for the printed nominal 1-inch copper Type L example.

Your pipe & operating inputs

mm
mm
m

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ID=OD−2t; capacity=πID²L/4.

Find bore and capacity for the printed nominal 1-inch copper Type L example.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Actual OD and wall are from a limited manufacturer reference sample, not an automatic selection of all ASTM B88 sizes.

Copper Type L Tube Capacity: assumptions and applications

Find bore and capacity for the printed nominal 1-inch copper Type L example. Actual OD and wall are from a limited manufacturer reference sample, not an automatic selection of all ASTM B88 sizes.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Copper Type L Tube Capacity Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Published nominal 1-inch tube OD = 28.575 mm; Published Type L wall = 1.27 mm; Straight pipe length = 3 m.

OutputComputed result
Actual calculated bore26.035 mm bore
Actual bore26.035 mm
Actual bore1.025 in
Flow area0.000532 m²
Internal capacity1.597079 L
Internal capacity0.421904 US gal
Internal capacity0.351308 Imp gal
Internal capacity0.0564 ft³
Internal capacity0.002089 yd³
Petroleum barrels (42 US gal)0.010045 bbl

How the stated input changes the result

ScenarioChanged input / basisResult
1.5 mStraight pipe length26.035 mm bore
2.25 mStraight pipe length26.035 mm bore
3 mStraight pipe length26.035 mm bore
3.75 mStraight pipe length26.035 mm bore
4.5 mStraight pipe length26.035 mm bore
6 mStraight pipe length26.035 mm bore

Unchanged inputs use: Dimension units = Metric (m / mm); Published nominal 1-inch tube OD = 28.575 mm; Published Type L wall = 1.27 mm; Straight pipe length = 3 m. Results retain the model limitations described above.

Common questions

Why is NPS different from measured inside diameter?

NPS is a nominal designation. Actual OD and the chosen wall schedule determine bore through ID=OD−2t.

Are the calculated tables full pipe standards?

No. They vary length for the single explicitly printed supplier dimension sample. They do not reproduce every nominal size or establish an allowable pressure.

How do I use this copper type l tube capacity calculator?

Find bore and capacity for the printed nominal 1-inch copper Type L example. ID=OD−2t; capacity=πID²L/4.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Mueller Streamline: copper tube reference information, PDF page 2https://muellerstreamline.com/download/streamline-copper-tube-pdf/?masterkey=5c00ae5073a74&wpdmdl=171
  • OpenStax Prealgebra: cylinder volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors