Pipe calculators / Nominal pipe & tube samples
Define the pipe. Follow the flow.
Copper Type K Tube Capacity Calculator
Find bore and capacity for the printed nominal 1-inch copper Type K example.
Your pipe & operating inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ID=OD−2t; capacity=πID²L/4.
Find bore and capacity for the printed nominal 1-inch copper Type K example.
- Confirm the fluid state, geometry, flow regime and units.
- Enter actual dimensions and justified operating conditions.
- Submit the form, then interpret the result with the assumptions and limits below.
Actual OD and wall are from a limited manufacturer reference sample, not an automatic selection of all ASTM B88 sizes.
Copper Type K Tube Capacity: assumptions and applications
Find bore and capacity for the printed nominal 1-inch copper Type K example. Actual OD and wall are from a limited manufacturer reference sample, not an automatic selection of all ASTM B88 sizes.
Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.
A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.
Continue with: NPS 1/2 Schedule 40S Pipe Calculator · NPS 1/2 Schedule 80S Pipe Calculator · NPS 3/4 Schedule 40S Pipe Calculator · NPS 3/4 Schedule 80S Pipe Calculator
Check the numbers
Copper Type K Tube Capacity Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Published nominal 1-inch tube OD = 28.575 mm; Published Type K wall = 1.651 mm; Straight pipe length = 3 m.
| Output | Computed result |
|---|---|
| Actual calculated bore | 25.273 mm bore |
| Actual bore | 25.273 mm |
| Actual bore | 0.995 in |
| Flow area | 0.000502 m² |
| Internal capacity | 1.504959 L |
| Internal capacity | 0.397568 US gal |
| Internal capacity | 0.331045 Imp gal |
| Internal capacity | 0.053147 ft³ |
| Internal capacity | 0.001968 yd³ |
| Petroleum barrels (42 US gal) | 0.009466 bbl |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 1.5 m | Straight pipe length | 25.273 mm bore |
| 2.25 m | Straight pipe length | 25.273 mm bore |
| 3 m | Straight pipe length | 25.273 mm bore |
| 3.75 m | Straight pipe length | 25.273 mm bore |
| 4.5 m | Straight pipe length | 25.273 mm bore |
| 6 m | Straight pipe length | 25.273 mm bore |
Unchanged inputs use: Dimension units = Metric (m / mm); Published nominal 1-inch tube OD = 28.575 mm; Published Type K wall = 1.651 mm; Straight pipe length = 3 m. Results retain the model limitations described above.
Common questions
Why is NPS different from measured inside diameter?
NPS is a nominal designation. Actual OD and the chosen wall schedule determine bore through ID=OD−2t.
Are the calculated tables full pipe standards?
No. They vary length for the single explicitly printed supplier dimension sample. They do not reproduce every nominal size or establish an allowable pressure.
How do I use this copper type k tube capacity calculator?
Find bore and capacity for the printed nominal 1-inch copper Type K example. ID=OD−2t; capacity=πID²L/4.
Can I calculate in metric and imperial units?
The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.
Can I export this calculation to Excel?
Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.
What do the starting values mean?
They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.
Where are the formula sources?
The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- Mueller Streamline: copper tube reference information, PDF page 2https://muellerstreamline.com/download/streamline-copper-tube-pdf/?masterkey=5c00ae5073a74&wpdmdl=171
- OpenStax Prealgebra: cylinder volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors