Pipe calculators / Geometry, volume & weight
Define the pipe. Follow the flow.
Water Filled Pipe Weight Calculator
Calculate theoretical mass from annular geometry and an explicitly entered density.
Your pipe & operating inputs
Your result
Ready to calculateEnter your values and press Calculate. The result will open on the calculation page.
Published references · Clear assumptions · No sign-up
The method
Formula and calculation steps
ID=OD−2t; wall mass=ρwall π(OD²−ID²)L/4.
Calculate theoretical mass from annular geometry and an explicitly entered density.
- Confirm the fluid state, geometry, flow regime and units.
- Enter actual dimensions and justified operating conditions.
- Submit the form, then interpret the result with the assumptions and limits below.
Densities are editable examples, not universal grade values. PVC example 1450 kg/m³ lies in a cited relative-density range 1.42–1.48; HDPE 959 applies only to the cited BorSafe HE3490-LS-H compound. Coatings, fittings and tolerances are excluded.
Water Filled Pipe Weight: assumptions and applications
Calculate theoretical mass from annular geometry and an explicitly entered density. Densities are editable examples, not universal grade values. PVC example 1450 kg/m³ lies in a cited relative-density range 1.42–1.48; HDPE 959 applies only to the cited BorSafe HE3490-LS-H compound. Coatings, fittings and tolerances are excluded.
Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.
A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.
Continue with: Pipe Volume Calculator · Pipe Internal Capacity Calculator · Water in Pipe Weight Calculator · Pipe Filling Time Calculator
Check the numbers
Water Filled Pipe Weight Calculator: calculated examples
These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.
Worked example with stated inputs
Dimension units = Metric (m / mm); Outside diameter = 60.3 mm; Wall thickness = 3.91 mm; Straight pipe length = 6 m; Wall material density (entered) = 7850 kg/m³; Fill liquid density = 998.2 kg/m³.
| Output | Computed result |
|---|---|
| Theoretical dimensioned pipe mass | 45.5802 kg |
| Empty wall mass | 32.624933 kg |
| Wall mass per metre | 5.437489 kg/m |
| Wall mass per foot | 3.653824 lb/ft |
| Total mass | 100.487139 lb |
| Actual bore | 52.48 mm |
| Actual bore | 2.066142 in |
| Flow area | 0.002163 m² |
| Internal capacity | 12.978628 L |
| Internal capacity | 3.428591 US gal |
| Internal capacity | 2.854899 Imp gal |
| Internal capacity | 0.458336 ft³ |
| Internal capacity | 0.016975 yd³ |
| Petroleum barrels (42 US gal) | 0.081633 bbl |
| Contained liquid mass | 12.955266 kg |
How the stated input changes the result
| Scenario | Changed input / basis | Result |
|---|---|---|
| 3 m | Straight pipe length | 22.7901 kg |
| 4.5 m | Straight pipe length | 34.18515 kg |
| 6 m | Straight pipe length | 45.5802 kg |
| 7.5 m | Straight pipe length | 56.97525 kg |
| 9 m | Straight pipe length | 68.3703 kg |
| 12 m | Straight pipe length | 91.160399 kg |
Unchanged inputs use: Dimension units = Metric (m / mm); Outside diameter = 60.3 mm; Wall thickness = 3.91 mm; Straight pipe length = 6 m; Wall material density (entered) = 7850 kg/m³; Fill liquid density = 998.2 kg/m³. Results retain the model limitations described above.
Common questions
What is the main limitation of this calculation?
Densities are editable examples, not universal grade values. PVC example 1450 kg/m³ lies in a cited relative-density range 1.42–1.48; HDPE 959 applies only to the cited BorSafe HE3490-LS-H compound. Coatings, fittings and tolerances are excluded.
How are the comparison-table numbers generated?
Each row changes the labelled straight pipe length from the worked example. The other printed inputs remain fixed. The table uses the same ID=OD−2t; wall mass=ρwall π(OD²−ID²)L/4. method as the form.
How do I use this water filled pipe weight calculator?
Calculate theoretical mass from annular geometry and an explicitly entered density. ID=OD−2t; wall mass=ρwall π(OD²−ID²)L/4.
Can I calculate in metric and imperial units?
The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.
Can I export this calculation to Excel?
Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.
What do the starting values mean?
They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.
Where are the formula sources?
The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.
Related calculators
Formula sources and references
References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.
- OpenStax Prealgebra: cylinder volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
- OpenStax University Physics: density is mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
- NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors