Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Gas, air & steam

Define the pipe. Follow the flow.

Steam Pipe Velocity Calculator

Calculate steam velocity from supplied mass flow, specific volume and actual bore.

Your pipe & operating inputs

mm
kg/h
m³/kg

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

Qactual=ṁ × specific volume; v=Qactual/A.

Calculate steam velocity from supplied mass flow, specific volume and actual bore.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Supply state-appropriate specific volume from a steam property source. No automatic steam table, wet-steam pressure drop or condensate return sizing.

Steam Pipe Velocity: assumptions and applications

Calculate steam velocity from supplied mass flow, specific volume and actual bore. Supply state-appropriate specific volume from a steam property source. No automatic steam table, wet-steam pressure drop or condensate return sizing.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Steam Pipe Velocity Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Actual inside diameter = 100 mm; Steam mass flow = 1000 kg/h; Supplied operating specific volume = 0.2 m³/kg.

OutputComputed result
Steam mean velocity at supplied state7.073553 m/s
Actual flow55.555556 L/s
Actual flow200 m³/h
US gallons per minute880.573508 US gpm
Imperial gallons per minute733.230828 Imp gpm
Actual cubic feet per minute117.715556 acfm

How the stated input changes the result

ScenarioChanged input / basisResult
500 kg/hSteam mass flow3.536777 m/s
750 kg/hSteam mass flow5.305165 m/s
1000 kg/hSteam mass flow7.073553 m/s
1250 kg/hSteam mass flow8.841941 m/s
1500 kg/hSteam mass flow10.61033 m/s
2000 kg/hSteam mass flow14.147106 m/s

Unchanged inputs use: Dimension units = Metric (m / mm); Actual inside diameter = 100 mm; Steam mass flow = 1000 kg/h; Supplied operating specific volume = 0.2 m³/kg. Results retain the model limitations described above.

Common questions

What is the main limitation of this calculation?

Supply state-appropriate specific volume from a steam property source. No automatic steam table, wet-steam pressure drop or condensate return sizing.

How are the comparison-table numbers generated?

Each row changes the labelled steam mass flow from the worked example. The other printed inputs remain fixed. The table uses the same Qactual=ṁ × specific volume; v=Qactual/A. method as the form.

How do I use this steam pipe velocity calculator?

Calculate steam velocity from supplied mass flow, specific volume and actual bore. Qactual=ṁ × specific volume; v=Qactual/A.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Spirax Sarco: Pipes and Pipe Sizinghttps://www.spiraxsarco.com/learn-about-steam/steam-distribution/pipes-and-pipe-sizing
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors