Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Geometry, volume & weight

Define the pipe. Follow the flow.

Pipe Weight Calculator

Calculate theoretical mass from annular geometry and an explicitly entered density.

Your pipe & operating inputs

mm
mm
m
kg/m³

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

ID=OD−2t; wall mass=ρwall π(OD²−ID²)L/4.

Calculate theoretical mass from annular geometry and an explicitly entered density.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Densities are editable examples, not universal grade values. PVC example 1450 kg/m³ lies in a cited relative-density range 1.42–1.48; HDPE 959 applies only to the cited BorSafe HE3490-LS-H compound. Coatings, fittings and tolerances are excluded.

Pipe Weight: assumptions and applications

Calculate theoretical mass from annular geometry and an explicitly entered density. Densities are editable examples, not universal grade values. PVC example 1450 kg/m³ lies in a cited relative-density range 1.42–1.48; HDPE 959 applies only to the cited BorSafe HE3490-LS-H compound. Coatings, fittings and tolerances are excluded.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe Weight Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Outside diameter = 60.3 mm; Wall thickness = 3.91 mm; Straight pipe length = 6 m; Wall material density (entered) = 7850 kg/m³.

OutputComputed result
Theoretical dimensioned pipe mass32.624933 kg
Empty wall mass32.624933 kg
Wall mass per metre5.437489 kg/m
Wall mass per foot3.653824 lb/ft
Total mass71.925666 lb
Actual bore52.48 mm
Actual bore2.066142 in
Flow area0.002163 m²
Internal capacity12.978628 L
Internal capacity3.428591 US gal
Internal capacity2.854899 Imp gal
Internal capacity0.458336 ft³
Internal capacity0.016975 yd³
Petroleum barrels (42 US gal)0.081633 bbl

How the stated input changes the result

ScenarioChanged input / basisResult
3 mStraight pipe length16.312467 kg
4.5 mStraight pipe length24.4687 kg
6 mStraight pipe length32.624933 kg
7.5 mStraight pipe length40.781167 kg
9 mStraight pipe length48.9374 kg
12 mStraight pipe length65.249867 kg

Unchanged inputs use: Dimension units = Metric (m / mm); Outside diameter = 60.3 mm; Wall thickness = 3.91 mm; Straight pipe length = 6 m; Wall material density (entered) = 7850 kg/m³. Results retain the model limitations described above.

Common questions

What is the main limitation of this calculation?

Densities are editable examples, not universal grade values. PVC example 1450 kg/m³ lies in a cited relative-density range 1.42–1.48; HDPE 959 applies only to the cited BorSafe HE3490-LS-H compound. Coatings, fittings and tolerances are excluded.

How are the comparison-table numbers generated?

Each row changes the labelled straight pipe length from the worked example. The other printed inputs remain fixed. The table uses the same ID=OD−2t; wall mass=ρwall π(OD²−ID²)L/4. method as the form.

How do I use this pipe weight calculator?

Calculate theoretical mass from annular geometry and an explicitly entered density. ID=OD−2t; wall mass=ρwall π(OD²−ID²)L/4.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Prealgebra: cylinder volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
  • OpenStax University Physics: density is mass per volumehttps://openstax.org/books/university-physics-volume-1/pages/14-1-fluids-density-and-pressure
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors