Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Geometry, volume & weight

Define the pipe. Follow the flow.

Pipe SDR and Wall Thickness Calculator

Calculate geometric wall thickness and bore from an entered diameter ratio.

Your pipe & operating inputs

mm
OD/t

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

t=OD/SDR; ID=OD−2t.

Calculate geometric wall thickness and bore from an entered diameter ratio.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

SDR alone does not determine allowable pressure without material, temperature, service and governing standard.

Pipe SDR and Wall Thickness: assumptions and applications

Calculate geometric wall thickness and bore from an entered diameter ratio. SDR alone does not determine allowable pressure without material, temperature, service and governing standard.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Pipe SDR and Wall Thickness Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Outside diameter = 110 mm; Standard dimension ratio = 11 OD/t.

OutputComputed result
Geometric wall thickness10 mm
Calculated bore90 mm

How the stated input changes the result

ScenarioChanged input / basisResult
55 mmOutside diameter5 mm
82.5 mmOutside diameter7.5 mm
110 mmOutside diameter10 mm
137.5 mmOutside diameter12.5 mm
165 mmOutside diameter15 mm
220 mmOutside diameter20 mm

Unchanged inputs use: Dimension units = Metric (m / mm); Outside diameter = 110 mm; Standard dimension ratio = 11 OD/t. Results retain the model limitations described above.

Common questions

What is the main limitation of this calculation?

SDR alone does not determine allowable pressure without material, temperature, service and governing standard.

How are the comparison-table numbers generated?

Each row changes the labelled outside diameter from the worked example. The other printed inputs remain fixed. The table uses the same t=OD/SDR; ID=OD−2t. method as the form.

How do I use this pipe sdr and wall thickness calculator?

Calculate geometric wall thickness and bore from an entered diameter ratio. t=OD/SDR; ID=OD−2t.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Prealgebra: cylinder volume and surface areahttps://openstax.org/books/prealgebra/pages/9-6-solve-geometry-applications-volume-and-surface-area
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors