Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Gas, air & steam

Define the pipe. Follow the flow.

Natural Gas Pipe Pressure Drop Calculator

Find natural gas downstream pressure from a supplied mass flow using the reduced isothermal relation.

Your pipe & operating inputs

mm
m
kPa absolute
K
J/(kg·K)
kg/h

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

p2=√[p1²−fD(L/D)(ṁ/A)² ZRT]; pressure drop=p1−p2.

Find natural gas downstream pressure from a supplied mass flow using the reduced isothermal relation.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Horizontal steady isothermal single-phase gas, constant supplied Z and Darcy factor, no fittings. The reduced relation is restricted here to outlet speed/√(ZRT) ≤0.3; no fuel-gas code sizing or certified line capacity. Representative gas properties are editable and must match the actual mixture.

Natural Gas Pipe Pressure Drop: assumptions and applications

Find natural gas downstream pressure from a supplied mass flow using the reduced isothermal relation. Horizontal steady isothermal single-phase gas, constant supplied Z and Darcy factor, no fittings. The reduced relation is restricted here to outlet speed/√(ZRT) ≤0.3; no fuel-gas code sizing or certified line capacity. Representative gas properties are editable and must match the actual mixture.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Natural Gas Pipe Pressure Drop Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Actual inside diameter = 25 mm; Straight pipe length = 30 m; Upstream absolute pressure = 700 kPa absolute; Gas temperature = 293.15 K; Specific gas constant = 518.3 J/(kg·K); Constant compressibility factor Z = 1 ; Darcy friction factor (entered) = 0.02 ; Gas mass flow = 20 kg/h.

OutputComputed result
Reduced isothermal pressure drop0.333713 kPa
Downstream absolute pressure699.666287 kPa absolute
Inside diameter25 mm
Outlet velocity2.45775 m/s
Outlet speed / sqrt(ZRT)0.006305

How the stated input changes the result

ScenarioChanged input / basisResult
10 kg/hGas mass flow0.083413 kPa
15 kg/hGas mass flow0.187694 kPa
20 kg/hGas mass flow0.333713 kPa
25 kg/hGas mass flow0.521496 kPa
30 kg/hGas mass flow0.751078 kPa
40 kg/hGas mass flow1.335808 kPa

Unchanged inputs use: Dimension units = Metric (m / mm); Actual inside diameter = 25 mm; Straight pipe length = 30 m; Upstream absolute pressure = 700 kPa absolute; Gas temperature = 293.15 K; Specific gas constant = 518.3 J/(kg·K); Constant compressibility factor Z = 1 ; Darcy friction factor (entered) = 0.02 ; Gas mass flow = 20 kg/h. Results retain the model limitations described above.

Common questions

Can I use this for a natural gas pressure-loss chart?

It gives the printed simplified physical model only. Gas code tables, regulator behavior, appliances, fittings, allowed pressure loss and mixture properties require a separate design basis.

Why is a negative pressure-square result rejected?

It means no positive downstream pressure can support the supplied flow under this reduced model. Increasing flow further is not a valid extrapolation.

How do I use this natural gas pipe pressure drop calculator?

Find natural gas downstream pressure from a supplied mass flow using the reduced isothermal relation. p2=√[p1²−fD(L/D)(ṁ/A)² ZRT]; pressure drop=p1−p2.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • Kowalczuk and Tatara (2020), Improved model of isothermal and incompressible fluid flow in pipelines versus the Darcy-Weisbach equation and the issue of friction factorhttps://doi.org/10.1017/jfm.2020.131
  • NASA Glenn: Equation of Statehttps://www1.grc.nasa.gov/beginners-guide-to-aeronautics/equation-of-state/
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors