Pipe Flow CalculatorFlow, pressure & pipe geometry

Pipe calculators / Geometry, volume & weight

Define the pipe. Follow the flow.

Elliptical Pipe Area Calculator

Calculate an ideal elliptical bore area and geometric capacity.

Your pipe & operating inputs

mm
mm
m

Starting values are editable examples. Verify actual bore, fluid state and model assumptions. Dimension switching converts only the labelled length fields; flow and property units stay as printed.

Reset

Your result

Ready to calculate

Enter your values and press Calculate. The result will open on the calculation page.

Published references · Clear assumptions · No sign-up

The method

Formula and calculation steps

A=π width height/4; capacity=A L.

Calculate an ideal elliptical bore area and geometric capacity.

  1. Confirm the fluid state, geometry, flow regime and units.
  2. Enter actual dimensions and justified operating conditions.
  3. Submit the form, then interpret the result with the assumptions and limits below.

Only the geometric ellipse is modeled; an arch or proprietary oval section may have a different area and wetted perimeter. No partial-depth hydraulic rating.

Elliptical Pipe Area: assumptions and applications

Calculate an ideal elliptical bore area and geometric capacity. Only the geometric ellipse is modeled; an arch or proprietary oval section may have a different area and wetted perimeter. No partial-depth hydraulic rating.

Use the actual measured bore rather than assuming a nominal pipe label equals its inside diameter. Schedule, lining, corrosion and deposits can change the effective flow area. Enter the applicable fluid properties at the operating temperature.

A flow rate, velocity, pressure difference and capacity describe different physical quantities. The stated model determines which additional measurements are needed. The calculated examples below vary one input while holding all other printed values fixed.

Check the numbers

Elliptical Pipe Area Calculator: calculated examples

These scenarios are computed with the same method as the form. They are not product recommendations, code design values or complete standards tables.

Worked example with stated inputs

Dimension units = Metric (m / mm); Internal full width = 500 mm; Internal full height = 300 mm; Straight pipe length = 10 m.

OutputComputed result
Ideal elliptical section area0.11781 m²
Internal capacity1,178.097245 L
Internal capacity311.220367 US gal
Internal capacity259.145165 Imp gal
Internal capacity41.604112 ft³
Internal capacity1.540893 yd³
Petroleum barrels (42 US gal)7.410009 bbl

How the stated input changes the result

ScenarioChanged input / basisResult
5 mStraight pipe length0.11781 m²
7.5 mStraight pipe length0.11781 m²
10 mStraight pipe length0.11781 m²
12.5 mStraight pipe length0.11781 m²
15 mStraight pipe length0.11781 m²
20 mStraight pipe length0.11781 m²

Unchanged inputs use: Dimension units = Metric (m / mm); Internal full width = 500 mm; Internal full height = 300 mm; Straight pipe length = 10 m. Results retain the model limitations described above.

Common questions

What is the main limitation of this calculation?

Only the geometric ellipse is modeled; an arch or proprietary oval section may have a different area and wetted perimeter. No partial-depth hydraulic rating.

How are the comparison-table numbers generated?

Each row changes the labelled straight pipe length from the worked example. The other printed inputs remain fixed. The table uses the same A=π width height/4; capacity=A L. method as the form.

How do I use this elliptical pipe area calculator?

Calculate an ideal elliptical bore area and geometric capacity. A=π width height/4; capacity=A L.

Can I calculate in metric and imperial units?

The dimension selector converts the labelled length inputs. Flow and property inputs retain their explicitly printed units. Results include related units where meaningful; US gallons and Imperial gallons are different units.

Can I export this calculation to Excel?

Calculate first, then use Export CSV for results and inputs. This is a numeric text export, not an Excel formula workbook, desktop application or certified engineering report.

What do the starting values mean?

They are editable numerical examples. Actual bore, fluid state, roughness, geometry and boundary conditions must match the installation. A calculated result is not a pressure rating or code sizing approval.

Where are the formula sources?

The sources below show plain-text addresses. Equations, examples and tables are stored in these pages; the calculator does not fetch source websites or JSON data files during use.

Formula sources and references

References support the underlying methods and units. Chosen example inputs are not universal recommendations, supplier ratings, market prices or code limits.

  • OpenStax Precalculus 2e: ellipse areahttps://openstax.org/books/precalculus-2e/pages/10-1-the-ellipse
  • NIST Guide to the SI: conversion factorshttps://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors